decking screws

I finally have all I need to complete the flooring., Including the cup of coffee. No, I don’t have the nail gun yet. Still waiting. So I picked up a box of decking screws to finish mounting the proboard.

 

first light & various electrical

I see the light!  FT and I installed the suite’s first light.  I decided on 4″ flush-mount LEDs throughout.  Also, the first tearing out of old electrical to make way for new circuits, including a 15A GFCI for the kitchen.  I’m getting pretty agile at crawling through the attic space.

 

shed floor framing

FT & I worked a little on the floor framing on the shed today.  I added the top sheathing of the partition wall.  Rene saw me holding the sheathing up and looking down at my screws & driver.  He helped hold it up whilst I fastened it to the framing.  It doesn’t quite meet the top, but it is a shed.

Cripples are hung on blocking where the 1/2″ plywood meet.

Then came landscape fabric and shovelling of the drainage gravel to fill in the gaps.

I was able to fit all of Rene’s stuff (carts & all) into his half of the shed.  Finally, no shopping carts in the yard!

Then came the fun part!  Power washing!

We began washing the fence, too, in preparation for paint.

 5/22/2022 10:38 AM      2763964 1403 3 Ave N Lethbridge AB 20220522_103839 shed sheathing partition.jpg
 5/22/2022 11:00 AM      2176716 1403 3 Ave N Lethbridge AB 20220522_110040 shed framing partition.jpg
 5/22/2022 11:00 AM      2348728 1403 3 Ave N Lethbridge AB 20220522_110044 shed framing partition.jpg
 5/22/2022 11:00 AM      2957841 1403 3 Ave N Lethbridge AB 20220522_110052 shed framing partition.jpg
 5/22/2022 12:22 PM      2649116 1403 3 Ave N Lethbridge AB 20220522_122242 shed floor framing cripple.jpg
 5/22/2022 12:37 PM      3723247 1403 3 Ave N Lethbridge AB 20220522_123756 shed front drainage gravel.jpg
 5/22/2022 12:38 PM      2522210 1403 3 Ave N Lethbridge AB 20220522_123806 shed front drainage gravel.jpg
 5/24/2022  9:19 AM      2582597 1403 3 Ave N Lethbridge AB 20220522_133203 shed storage.jpg
 5/22/2022  1:32 PM      2436052 1403 3 Ave N Lethbridge AB 20220522_133218 shed storage.jpg
 5/24/2022  9:20 AM      8180540 1403 3 Ave N Lethbridge AB 20220522_133230 shed partition, storage.jpg
 5/22/2022  1:32 PM      6877176 1403 3 Ave N Lethbridge AB 20220522_133249 shed storage panorama.jpg
 5/22/2022  1:33 PM      2186522 1403 3 Ave N Lethbridge AB 20220522_133323 shed Rene's carts.jpg
 5/22/2022  1:33 PM      2550477 1403 3 Ave N Lethbridge AB 20220522_133328 shed Rene's stuff.jpg
 5/22/2022  3:08 PM      3937090 1403 3 Ave N Lethbridge AB 20220522_150810 shed power wash.jpg
 5/24/2022  9:22 AM      4185669 1403 3 Ave N Lethbridge AB 20220522_150816 shed Floyd power wash.jpg
 5/22/2022  3:08 PM      3944408 1403 3 Ave N Lethbridge AB 20220522_150823 shed Floyd power wash.jpg
 5/22/2022  3:09 PM      1713196 1403 3 Ave N Lethbridge AB 20220522_150948 shed Floyd power wash, Allan.jpg
 5/22/2022  3:09 PM      4157299 1403 3 Ave N Lethbridge AB 20220522_150957 shed power wash.jpg
 5/22/2022  4:17 PM      3933268 1403 3 Ave N Lethbridge AB 20220522_161704 shed Floyd power wash.jpg
 5/22/2022  5:13 PM      4247196 1403 3 Ave N Lethbridge AB 20220522_171356 fence power wash.jpg
 5/22/2022  5:14 PM      3214361 1403 3 Ave N Lethbridge AB 20220522_171400 shed power washed.jpg

new shed plywood & OSB

Building material prices have gone up and down a lot lately.  I picked up a few sheets of OSB & plywood for the shed today.  We have to cut the bottom off the exterior sheathing (rotten, chipped, dried, dirty, ugly) and put an actual floor in it.

 5/16/2022  2:20 PM      2911152 1403 3 Ave N Lethbridge AB 20220516_142022 shed Floyd.jpg
 5/16/2022  3:33 PM      2654693 1403 3 Ave N Lethbridge AB 20220516_153340 shed plywood & OSB on van roof.jpg
 5/16/2022  4:12 PM      2839351 1403 3 Ave N Lethbridge AB 20220516_161235 shed framing floor.jpg
 5/24/2022  8:52 AM      2200617 1403 3 Ave N Lethbridge AB 20220516_161238 shed Floyd.jpg

shed on beams

We put the shed on 4×4 treated beams today.  What a task!  This shed is heavy and likes to bend into a parallelogram.

 5/15/2022  6:05 PM      3605537 1403 3 Ave N Lethbridge AB 20220515_180521 shed setting on beams.jpg
 5/15/2022  6:05 PM      3210123 1403 3 Ave N Lethbridge AB 20220515_180532 shed setting on beams.jpg
 5/15/2022  6:05 PM      2378713 1403 3 Ave N Lethbridge AB 20220515_180538 shed setting on beams.jpg
 5/15/2022  6:05 PM      2921104 1403 3 Ave N Lethbridge AB 20220515_180542 shed setting on beams.jpg
 5/15/2022  6:05 PM      2722152 1403 3 Ave N Lethbridge AB 20220515_180548 shed setting on beams.jpg

not a stitch of insulation

I learned today that this old house has no insulation!  There is nothing in the attic of the main floor, and there appears to be nothing in the walls, either.  I took the trim off the top of the kitchen window, and there appears to be nothing there.

I found Sunny South Insulators at the Home & Garden show this spring.  A guy came out to have a look, and this is what we found – nothing.  So, it will be $8500 to blow in insulation into the ceiling and walls.

tub surround

The project for today was removal of the glue at the tub surround.  It was cracked in many places.  It had to be replaced.  Behind it though was a truckload of glue that was basically just squirted on in an S shape without being trowelled.  The result was large gaps where the surround plastic was bulging away from the wall, creating ample opportunity for someone to lean on it and crack it.  In some places, the surround was glued in place a good quarter inch (0.7cm) away from the wall.

Read more

CNC

I have a new CNC coming!  With the help of my college cronies (thank you, T & R), I chose the Maker Made M2 kit.  It’s a hobbyist apparatus that stands upright (not flat, like a table).  The website states that it is capable of cutting 4×8 sheets, but others who have used it say it can do larger.  Needless to say, it’s not comparable to larger professional CNC machines with vacuum sheet movers, automated switching of router bits, and lasers to guide it all.  It’s a beginner’s CNC.  More later when it arrives.